Laser Cutting Machine

6 Methods to Improve the Laser cutting efficiency

6 Methods to Improve the Laser cutting efficiency

Estimated reading time: 10 minutes

In recent years, the role of laser cutting machines in the development of the sheet metal industry has become increasingly prominent. During the cutting process, there are six practical functions. With these practical functions, the processing efficiency and cutting performance of the laser cutting machine can be greatly improved.


Leapfrogging is the idle way of laser cutting machines. As shown in the figure below, after cutting the hole, the cutting hole and head must move from point A to point B. Of course, the laser must be turned off during the movement. In the moving process from point A to point B, the machine runs “empty”, which is called idling.

laser cutting efficiency

The idle stroke of the early laser cutting machine is shown in the following figure. The cutting head has to complete three actions: ascending (to a sufficiently safe height), translation (arriving above point B), and descending.

laser cutting efficiency

Compressing the idle time can improve the efficiency of the machine. If the next three actions are completed “simultaneously”, the idle time can be shortened: when the cutting head starts from point A to point B, it rises at the same time; when it approaches point B, it falls at the same time. As shown below.

frog jumping

The trajectory of the cutting head’s idle motion is like an arc drawn by a frog jumping.

In the development process of the laser cutting machine, the leapfrog can be regarded as an outstanding technological advancement. Leapfrogging only takes up the translational time from point A to point B, and saves the time of ascent and descent. The frog jumped and caught the food; the frog jump of the laser cutting machine “caught” high efficiency. If the laser cutting machine does not have the leapfrog function, I am afraid it will not enter the market.

Auto Focus

When cutting different materials, the focus of the laser beam is required to fall at different positions on the cross-section of the work piece. Therefore, it is necessary to adjust the position of the focus (focus). Early laser cutting machines generally used manual focusing; now, many manufacturers’ machines have achieved automatic focusing.

Some people may say that just changing the height of the cutting head is good. When the cutting head is raised, the focus position will be higher, and when the cutting head is lowered, the focus position will be lower. It’s not that simple.

In fact, during the cutting process, the distance between the nozzle and the work piece (nozzle height) is about 0.5~1.5mm, which may be regarded as a fixed value, that is, the nozzle height does not change, so the focus cannot be adjusted by raising and lowering the cutting head (otherwise Unable to complete the cutting process).

The focal length of the focusing lens is immutable, so you cannot expect to adjust the focus by changing the focal length. If you change the position of the focus lens, you can change the focus position: the focus lens goes down, the focus goes down, and the focus lens goes up, the focus goes up. ——This is indeed a way of focusing. A motor is used to drive the focusing lens to move up and down to achieve automatic focusing.

Another automatic focusing method is: before the beam enters the focusing mirror, a variable curvature mirror (or adjustable mirror) is set, and the divergence angle of the reflected beam is changed by changing the curvature of the mirror, thereby changing the focus position. As shown below.

laser cutting efficiency

With the automatic focusing function, the processing efficiency of the laser cutting machine can be significantly improved: the perforation time of thick plates is greatly reduced; when processing workpieces of different materials and different thicknesses, the machine can automatically quickly adjust the focus to the most suitable position.

Automatic Edge Finding

As shown in the figure below, when the sheet is placed on the workbench, if it is skewed, it may cause waste during cutting. If the inclination angle and origin of the sheet can be sensed, the cutting process can be adjusted to suit the angle and position of the sheet to avoid waste. The automatic edge finding function came into being.

After the automatic edge finding function is activated, the cutting head starts from point P and automatically measures 3 points on the two vertical edges of the sheet: P1, P2, P3, and automatically calculates the inclination angle A of the sheet and the origin.

With the help of the automatic edge finding function, it saves the time of adjusting the work piece earlier-it is not easy to adjust (move) work pieces weighing hundreds of kilograms on the cutting table, which improves the efficiency of the machine.

A high-power laser cutting machine with advanced technology and powerful functions is a complex system integrating light, machine, and electricity. The subtlety often hides the mystery. Let us explore the mystery together.

Centralized Perforation

Centralized perforation, also known as pre-perforation, is a processing technology, not a function of the machine itself. When laser cutting thicker plates, each contour cutting process has to go through two stages: 1. perforation and 2. cutting.

laser cutting efficiency

Conventional processing technology (point A perforation→cut contour 1→point B perforation→cut contour 2→……), the so-called centralized perforation, is to carry out all the perforation processes on the entire board in advance, and then perform the cutting process again.

laser cutting efficiency

Concentrated piercing processing technology (complete perforation of all contours→return to starting point→cutting all contours). Compared with conventional processing technology, the total length of the machine’s running track is increased during concentrated piercing. Then why use concentrated piercing?

Concentrated perforation can avoid over-burning. During the perforation process of the thick plate, heat accumulation is formed around the perforation point. If it is cut immediately, overburning will occur. The centralized perforation process is adopted to complete all perforations and return to the starting point for cutting. Since there is sufficient time to dissipate heat, overburning is avoided.

laser cutting efficiency

Centralized perforation can improve processing efficiency. At present, there are still many laser cutting machines that do not have the function of automatic focusing. The process parameters (laser mode, power, nozzle height, auxiliary gas pressure, etc.) of the two stages of processing thick plates, perforating, and cutting are different. The height of the nozzle during the piercing process is higher than that of the cutting process. If the conventional processing technology is adopted (contour 1 perforation→contour 1 cutting→contour 2 perforation→contour 2 cutting→……), in order to ensure the cutting quality and efficiency, the focus of the laser beam can only be manually adjusted to the best according to the cutting needs Position (Imagine if this is the case: at first, manually set the focus to the position required for the piercing, pierce; then, adjust the focus to the position required for cutting, cut; then adjust to the piercing position, pierce; …; Until the processing is completed-this is simply a nightmare). Therefore, the focus during perforation must not be at the optimal position, and the perforation time is longer. However, if the centralized perforation method is adopted, the focus can be adjusted to a position suitable for the perforation first, after the perforation is completed, the machine is paused, and then the focus position is adjusted to the best position required for cutting; in this way, the perforation time can be shortened by more than half, greatly improve efficiency. Of course, if necessary, other process parameters can be adjusted or changed between concentrated piercing and cutting (for example, air + continuous wave can be used for piercing, and oxygen can be used for cutting, and there is enough time to complete the gas switch). We generally call the automatic zoom of the driving focus lens the F axis; like this, the manual zoom is used to concentrate the piercing and cutting, can it be called the “H” (Hand) axis “zoom”?

Concentrated piercing is also risky. If a collision occurs during the cutting process, which causes the position of the plate to change, the part that has not been cut may be scrapped. The centralized perforation process requires the help of an automatic programming system.

Bridge Position (micro connection)

During the laser cutting process, the sheet material is supported by the serrated support bar. If the cut part is not small enough, it cannot fall from the gap of the support bar; if it is not big enough, it cannot be supported by the support bar; it may lose its balance and warp. The cutting head moving at high speed may collide with it, and the cutting head may be damaged in the light of the shutdown.

This phenomenon can be avoided by using the bridge position (micro-connection) cutting process. When programming the graphics for laser cutting, the closed contour is intentionally broken in several places, so that after the cutting is completed, the parts adhere to the surrounding materials without falling. These broken places are the bridges. Also known as a breakpoint, or micro-connection (this name is derived from the blunt translation of MicroJoint). The distance of the break, about 0.2~1mm, is inversely proportional to the thickness of the sheet. Based on different angles, there are these different names: based on the contour, it is disconnected, so it is called a breakpoint; based on the part, it adheres to the base material, so it is called a bridge or a micro-connection.

breakpoint laser cutting efficiency

The bridge position connects the parts with the surrounding materials. The mature programming software can automatically add the appropriate number of bridge positions according to the length of the contour. It can also distinguish the inner and outer contours, and decide whether to add bridges so that the inner contours (waste) that do not leave the bridges will fall, and the outer contours (parts) of the bridges will be glued together with the base material and will not fall, thereby avoiding Sorting work.

Common Edge Cutting

If the contours of adjacent parts are straight lines and the angles are the same, they can be combined into a straight line and cut once. This is the common edge cutting. Obviously, edge cutting reduces the cutting length and can significantly improve processing efficiency.laser cutting efficiency

Co-edge cutting does not require the shape of the part to be rectangular. As shown below.


The sky blue lines are common edges, and the common edges are cut, which not only saves cutting time, but also reduces the number of perforations. Therefore, the benefits are very obvious. If you save 1.5 hours a day due to common edge cutting, about 500 hours are saved every year, and the hourly comprehensive cost is 100 yuan, which is equivalent to creating an additional 50,000 yuan benefit a year. Common edge cutting needs to rely on intelligent automatic programming software. laser cutting efficiency.

Related Posts

One thought on “6 Methods to Improve the Laser cutting efficiency

  1. Avatar of ali ali says:

    learn it

Leave a Reply

Your email address will not be published. Required fields are marked *